Electric Pool Cover Won't Open

It seems like the bearings in the motor are stuck. Our automatic pool covers open and close at the touch of a button encouraging heat retention chemical savings and a longer swimming season all with an unobtrusive design that will never clash with your landscaping.

Best Pool Cover Reviews 2021 Top Picks For 6 Common Situations

Get rid of water from top.

Electric pool cover won't open. Press the pin into the housing in the deck until it clicks into place. Never leave the cover partially open. Reset breakers or the GFI if necessary.

Make sure there is nothing interfering with the cover operation before adjusting the slip clutch. Clear debris off the pump and out of the drains. Low levels may prevent the cover from operating.

Pull a few feet of rope from the rope reels. T4 Spa Automatic Spa Cover Owners Manual. In those early moments service technicians should focus less on hurriedly getting the problem fixed and instead take an investigative approach before handling any equipment.

We pull the ropes all the way out. Save-T 3 Automatic Pool Cover Owners Manual Mar 2012 or later Step-Saver Manual Pool Cover Owners Manual Mar 2011 Rel-0007 Autosave Spa Cover Owners Manual Mar 2010 or later. If the clutch is slipping due to the reasons above fix the.

However cover didnt move at all. The cover wont open. It hums however it doesnt turn at all.

Never operate the cover while someone is in the pool or spa. If its lighting up but failing. Contact Automatic Pool Covers Inc.

Measure from the roll up tube to the bottom of the level on both the motor end and non motor end of the mechanism. Clean out the Box. Position a level across the housing.

Using the ratchet is the easier tool to use. We only managed to open the cover maybe 10 inches. T4 Versa Automatic Pool Cover Owners Manual.

Maintain pool water at a proper level. Remove clamps and guides then drive plastic anchors 33 into each hole. Well have to inspect the electrical system to see if the cover is getting power.

Adjust height of the non-motor end feet if needed to level the roll-up tube. Our neighbors who dont have an auto cover opened two days after we did after professionally closing to a BLACK pool. 3 deep on a slight angle toward the pool wall.

A few gallons is OK even 10 or 15 but more than that puts a strain on the motor reels and ropes. The reasons could be. Finally fasten the guides to the underside of the coping with 12 screws 26.

Once you have the cover moving well on its own then the next thing I would check is the slip clutch. I think disconnecting the motor should help temporarily. Pull ropes equally on either side until the cover is in place.

Load or a person standing on the cover it may force the leading edge open enough to allow a child to slip through the opening. When the cover wont open it may signify there is no power to the system. Do not flood the drain or motor damage may occur.

Save-T 3 Automatic Pool Cover Owners Manual This pool cover has been installed with the following features. They actually put in a call to their PB to see how much it. Thats when we tried to use a channel locks to turn it.

Tion of the cover. A pool toy pine needles sand or other types of debris may be activating. Walk on the cover in an emergency situation only.

Is committed to innovative technology and cutting-edge manufacturing and every automatic pool cover they make is built with commercial grade components which means you can count on the fact that your pool cover will open and close quickly every time. Put the pin through the grommet in the strap. If your touchpad has backlighting feature does it illuminate.

Insert the key into the top of the pin. Evaluating the pool cover site Every service request must start off with a five- to 10-minute evaluation of the entire pool cover site. If your mechanism does not have this adapter there are two different tools shown that can also help you manually open the cover.

Put the pin. Check the breakers and switches. ANNUAL AUTO COVER MAINTENANCE To protect your cover do three things at least once per year and some may need 2-3 times per year.

8 Position the mechanism in the cover box so that the roll-up tube is centered in the cover. If water is in the pool place the hammer drill with a 14 masonry carbide-tipped bit into a large bucket Drill holes approx. Its likely that the tracks are blocked.

The Cover Wont Open or Close All the Way. It may be necessary to remove the lid to accomplish this and to unroll the fabric a little manually before pulling it into the track. The cover could be running crooked or there could be an object blocking the cover.

Remove the water or blocking object. Heres a quick checklist. Never Open or Close an automatic cover with large puddles of water.

Water on the cover low pool water level bad track pulleys and dirt or debris in the track can all cause the clutch to slip. If the pool cover motor is running but the cover will not open the issue is mechanical. Load or a person standing on the cover it may force the leading edge open enough to allow a child to slip through the opening.

Automatic Pool Covers Inc. If that doesnt solve the issue please call Cover Care. Well likely have to repair or replace a part to get the cover to open.

Check your tracks for any obvious obstacles. A wire connector is provided on this unit to connect a minimum no. If you are not able to get the cover open or have any questions please call the front office for service we can be reach toll free at 1-877-473-2943.

8 awg 84mm² solid copper conductor between this unit and any metal equipment metal enclosures of electrical equipment metal. Slip Clutch Auto-shutoff CoverLink Control Pad. This happens to them every year and its at least a week before they can swim.

We take pride in providing a safer and more efficient environment for pool owners. Pump excess water off the. T4 Automatic Pool Cover Owners Manual.

One of circuit breakers tripped Motor in need of service Water on cover making it heavier Cover stuck to deck surface Water in the tube where cover gets rolled Reset any circuit breaker if tripped. Torque level is too low. Ad Free Shipping Available.

If red light continues to blink call for service. When the pool water level is to low the pool cover motor will have to pull hard and the amp limiter on the control pad will sense the problem and a red light. CoverPro has you covered.

Remove the bolt from the coupler 080027 or the motor side of the slip clutch whichever you have.

Swimming Pool Covers And Their Impact On Water Chemistry